Understand the problem

Damp, mould and building defects explained.

Many defects look alike. A stain, patch of mould or damaged plaster shows where a problem appears, but it may not show where the moisture comes from. Use this guide to understand the possibilities and the questions a survey can answer.

Explore the common signs ↓
01 / Condensation02 / Mould03 / Penetrating damp04 / Ground level moisture05 / Leaks and old staining06 / Timber defects

Start with evidence

Similar symptoms. Different causes.

Cold surfaces, rainwater entry, leaks and moisture from the ground can produce overlapping signs. More than one cause may be present. Position, timing, weather, ventilation, construction and the condition of the building all matter.

A photograph or meter reading is not a diagnosis.These descriptions are starting points. A survey considers the whole pattern, and concealed areas may need a separate agreed inspection.
01 / Moisture in the air

Condensation

Warm, moist indoor air can leave water on colder surfaces. Windows, external corners and areas behind furniture are common places to notice it.

What you might notice

Water on glass, damp corners or patches that worsen in colder weather. Mould may follow where a surface stays damp.

Possible contributors

Ventilation, heating, insulation, cold bridges and everyday moisture all affect the balance. A blocked or ineffective extractor can be part of the picture.

What we investigate

We consider surface temperatures, humidity, airflow, ventilation provision and the building fabric, alongside any signs of leaks or water entry.

Explore mould and condensation surveys ↗
02 / Visible growth

Mould

Mould needs moisture. Cleaning visible growth may remove the symptom for a time, while the source of dampness remains.

What you might notice

Recurring spots or patches on walls, ceilings, window reveals or furnishings, sometimes with a musty smell.

Possible contributors

Condensation on cold surfaces is common, but leaks, water entry or other moisture sources can also be involved.

What we investigate

We look at the location and pattern of growth, moisture conditions, ventilation, cold surfaces and relevant building defects.

Explore mould and condensation surveys ↗
03 / Water from outside

Penetrating damp

Rainwater may enter through a defect in the external fabric and appear somewhere else inside the building.

What you might notice

Localised staining, peeling finishes or dampness after rainfall. The affected area may be near a window, roof junction or chimney.

Possible contributors

Defective gutters, roof coverings, flashings, pointing, render or seals can let water in. The route depends on the building.

What we investigate

We compare the internal pattern with accessible external details, exposure to rain and the history of the problem.

Explore damp surveys ↗
04 / Lower walls and floors

Ground level moisture

Damp at the base of a wall can have several explanations. Its height alone does not establish rising damp.

What you might notice

Damaged skirting, salts, flaking paint or deteriorated plaster near floor level.

Possible contributors

Ground levels, drainage, bridging, plumbing, condensation and moisture moving through the structure may all need consideration.

What we investigate

We review construction, external levels, drainage, moisture patterns and previous treatments before recommending work.

Explore damp surveys ↗
05 / Services and previous damage

Leaks and old staining

A plumbing or roof leak can leave a visible mark long after the water source has been repaired. New staining may indicate an active problem.

What you might notice

Ceiling marks, localised wet patches, damaged finishes or stains that return after decorating.

Possible contributors

Pipework, bathrooms, roof junctions and rainwater goods may be involved. Residual moisture or salts can affect old finishes.

What we investigate

We review the repair history, accessible adjoining areas and moisture evidence. A concealed source may require further investigation.

Explore building pathology ↗
06 / Related defects

Timber decay and woodworm

Moisture and limited airflow can affect timber. Flight holes, softness or fungal growth deserve assessment in context.

What you might notice

Soft or crumbling timber, fungal growth, distorted floors or small holes in wood.

Possible contributors

Long term dampness, leaks or poor sub floor ventilation can support decay. Holes alone do not prove current insect activity.

What we investigate

We inspect accessible timber, moisture sources and ventilation, then explain where opening up may be needed.

Explore timber surveys ↗

The next step

Tell us what you have noticed.

We can help choose the right survey for your property and explain its scope before you book.

Further reading

For wider guidance on moisture and building condition, see UK government guidance on damp and mould and Historic England’s guide to assessing damp in older buildings.